POA
Olimpic 500 is a complete and versatile edgebander for SME’s able to perform different machining operations, in a small space, always with high quality standards.
Available in both pneumatic and electronic set-up versions, olimpic 500 allows machining with 2 radii, each with dedicated tool and panels with a minimum width of 60 mm.
GENERAL FEATURES
Automatic single-sided edge bander for the application and gluing of edges with hot melt glue on straight panels, on the four panel sides and the finishing and rounding-off of the panel corners.
Main frame made of bended and welded steel plates. Highly stiff and vibration-free structure. Openings with shoots for the removal of chips to the floor that are not collected by the dust extraction.
Top steel presser complete with two rows of rubber coated wheels mounted on bearings. Cover for wheel protection. Automatic lifting of presser from machine control.
Panel infeed area consisting of a support table and lateral guide for a correct panel insertion.
Light-signaling device positioned on the machine infeed side indicating the correct distance of panel insertion and the operating status of the machine, by different colors.
Top working units fixed on the presser, while bottom working units fixed to the horizontal beam for a precise reference with respect to the panel.
All frequency motors are equipped with inverter.
Safety cabin on the entire length of the machine with polycarbonate windows for the unit viewing during machining.
2 doors provide access to the working units, one for the gluing area and one for the finishing area. Doors have independent management of each other.
Exhaust outlets for the operating units are positioned on the top side of the safety cabin.
Control panel in an ergonomic position at machine infeed for an easy use from the operator’s working position
Electrical cabinet positioned inside the main frame with doors that allow an easy access in case of any maintenance operations. The cabinet is in conformity with the current safety regulations.
Panel handling by means of feed track consisting of pads coated with high friction rubber and ¾ link industrial chain.
Sliding of pads on two guideways, one round and one flat, to ensure straightness of movement and resistance to side loads.
Manual pads lubrication.
Panel support rollers positioned parallel to the track on the entire length of the machine with telescopic opening system and sliding plastic wheels with steel pivot pins.
In Stock
For more information
If you are looking to swap out your older machine for a brand new model, fill in this short form.
Finance available on this machine working alongside our partner Close Brothers Asset Finance.
IMPORTANT
Specifications | |
---|---|
Make | |
Model | |
Pre Milling Unit | |
Minimum Panel Length | |
Edge Thickness | |
Minimum Panel Thickess | |
End Trim | |
Motor Power | |
Corner Rounded | |
Scraping |
Specifications | |
---|---|
Bander Type | |
Feed Speed | |
Maximum Edge Thickness | |
Minimum Edge Thickness | |
Top/bottom Trim | |
Buffing | |
Dust Outlet Size | |
Voltage/Phase | |
Weight | |
Dimensions |
FEATURES
TECHNICAL DATA | ||
Feed speed | m/min | 12 |
Panel thickness | mm | 8 – 60 |
Strip edge thickness | mm | 0,3 – 6 |
Coiled edge thickness | mm | 0,3 – 3 |
Max section of coiled edge | mm² | 135 |
Coil-holder plate diameter | mm | 780 |
Edge exceeding with respect to the panel thickness *(5 mm with max 3 mm edge thickness) | mm | 2+3 (5)* |
Panel distance: | ||
– without rounding unit | mm | 600 |
– with rounding unit | mm | 650 |
Minimum panel length | mm | 140 |
Minimum coiled edge length | mm | 180 |
Minimum strip edge length | mm | 220 |
Minimum panel width – lengthwise pass: | ||
*<=25 mm panel thickness, 240 mm minimum panel length | mm | 60 |
* >25 mm panel thickness or > 3 mm edge, 210 mm minimum panel length | mm | 90 |
Minimum panel dimensions for 4 side machining | mm | 140 x 140 |
Minimum panel dimensions for lengthwise machining only (LxW) | mm | 240 x 60 |
Panel roller support opening | mm | 500 |
Work table height | mm | 900 |
R0.07.15 | olimpic 500 – composition “HP T-ER2” (40) |
Electronic top presser positioning | |
62.10.74 | Panel spacer on infeed fence |
62.15.03 | “Nesting” copying device kit |
62.12.03 | “AAR” anti-adhesive unit |
62.12.61 | Spray-mist device for edge finishing |
62.12.96 | Spray-mist device for delicate edges |
“RT-V1” pre-milling unit | |
62.14.55 | Diamond tools for pre-milling unit H=64-no.2 knives |
“VC-VM” gluing unit | |
62.12.49 | Infrared ceramic lamp |
62.15.08 | SGP-E additional glue pot – manual glue supply (1,5 Kg) |
“K-2 Radius” end cutting unit | |
“R-HP Multiedge 2R” trimming-chamfering unit | |
“Round 2-A Multiedge 1R” rounding unit | |
“RAS-HP Multiedge 2R” edge scraping unit | |
62.15.04 | “RC-N” glue scraping unit |
62.12.12 | “SP-V” brushing unit |
“eye-S” consolle (Control-Panel) | |
“Maestro active edge” human-machine interface software (HMI) | |
Qs Monitor software equipment for “eye-S” | |
Maestro connect: basic set-up (cabling only, for later gateway installation) | |
10.09.98 | European safety regulations (CE norms) |
93.07.31 | Volt 400 EU |
PRODUCTS
If you can’t find a product you need on our website, our team will be able to help you source it. Contact us today!
RJ Woodworking Machinery began trading more than 30 years ago with the simple vision to be one of the best providers of woodworking machinery and equipment in the UK.
Monday – Friday: 8:30am – 17:00pm
© Copyright 2024 - RJ Woodworking Machinery. All rights reserved. Website by Sood
"*" indicates required fields
"*" indicates required fields
NEW PRODUCT
SCM Multiblade M3 Rip Saw 35hp
The SCM Multiblade M3 Rip Saw 35hp is a heavy-duty feed track that ensures any vibrations in the machining process are absorbed away from the workpiece. This reliable, durable and accurate machine will ensure safety and efficiency whilst proving great value for money.