Customise Consent Preferences

We use cookies to help you navigate efficiently and perform certain functions. You will find detailed information about all cookies under each consent category below.

The cookies that are categorized as "Necessary" are stored on your browser as they are essential for enabling the basic functionalities of the site. ... 

Always Active

Necessary cookies are required to enable the basic features of this site, such as providing secure log-in or adjusting your consent preferences. These cookies do not store any personally identifiable data.

No cookies to display.

Functional cookies help perform certain functionalities like sharing the content of the website on social media platforms, collecting feedback, and other third-party features.

No cookies to display.

Analytical cookies are used to understand how visitors interact with the website. These cookies help provide information on metrics such as the number of visitors, bounce rate, traffic source, etc.

No cookies to display.

Performance cookies are used to understand and analyze the key performance indexes of the website which helps in delivering a better user experience for the visitors.

No cookies to display.

Advertisement cookies are used to provide visitors with customized advertisements based on the pages you visited previously and to analyze the effectiveness of the ad campaigns.

No cookies to display.

SCM Olimpic 500 HP-TER2 Compact Automatic Edgebander.

POA

Olimpic 500 is a complete and versatile edgebander for SME’s able to perform different machining operations, in a small space, always with high quality standards.

Available in both pneumatic and electronic set-up versions, olimpic 500 allows machining with 2 radii, each with dedicated tool and panels with a minimum width of 60 mm.

GENERAL FEATURES

Automatic single-sided edge bander for the application and gluing of edges with hot melt glue on straight panels, on the four panel sides and the finishing and rounding-off of the panel corners.

 

Main frame made of bended and welded steel plates. Highly stiff and vibration-free structure. Openings with shoots for the removal of chips to the floor that are not collected by the dust extraction.

 

Top steel presser complete with two rows of rubber coated wheels mounted on bearings. Cover for wheel protection. Automatic lifting of presser from machine control.

 

Panel infeed area consisting of a support table and lateral guide for a correct panel insertion.

Light-signaling device positioned on the machine infeed side indicating the correct distance of panel insertion and the operating status of the machine, by different colors.

 

Top working units fixed on the presser, while bottom working units fixed to the horizontal beam for a precise reference with respect to the panel.

All frequency motors are equipped with inverter.

 

Safety cabin on the entire length of the machine with polycarbonate windows for the unit viewing during machining.

2 doors provide access to the working units, one for the gluing area and one for the finishing area. Doors have independent management of each other.

 

Exhaust outlets for the operating units are positioned on the top side of the safety cabin.

 

Control panel in an ergonomic position at machine infeed for an easy use from the operator’s working position

 

Electrical cabinet positioned inside the main frame with doors that allow an easy access in case of any maintenance operations. The cabinet is in conformity with the   current safety regulations.

 

Panel handling by means of feed track consisting of pads coated with high friction rubber and ¾ link industrial chain.

Sliding of pads on two guideways, one round and one flat, to ensure straightness of movement and resistance to side loads.

Manual pads lubrication.

 

Panel support rollers positioned parallel to the track on the entire length of the machine with telescopic opening system and sliding plastic wheels with steel pivot pins.

 

 

Part Exchange

If you are looking to swap out your older machine for a brand new model, fill in this short form.

Finance Enquiry

Finance available on this machine working alongside our partner Close Brothers Asset Finance.

IMPORTANT

Technical Specifications

Specifications
Make
Model
Pre Milling Unit
Minimum Panel Length
Edge Thickness
Minimum Panel Thickess
End Trim
Motor Power
Corner Rounded
Scraping
Specifications
Bander Type
Feed Speed
Maximum Edge Thickness
Minimum Edge Thickness
Top/bottom Trim
Buffing
Dust Outlet Size
Voltage/Phase
Weight
Dimensions

FEATURES

Machines Features

Specifications

TECHNICAL DATA
Feed speedm/min12
Panel thicknessmm8 – 60
Strip edge thicknessmm0,3 – 6
Coiled edge thicknessmm0,3 – 3
Max section of coiled edgemm²135
Coil-holder plate diametermm780
Edge exceeding

with respect to the panel thickness

*(5 mm with max 3 mm edge thickness)

mm2+3 (5)*
Panel distance:
– without rounding unitmm600
– with rounding unitmm650
Minimum panel lengthmm140
Minimum coiled edge lengthmm180
Minimum strip edge lengthmm220
Minimum panel width – lengthwise pass:
*<=25 mm panel thickness,
240 mm minimum panel length
mm60
* >25 mm panel thickness or > 3 mm edge, 210 mm minimum panel lengthmm90
Minimum panel dimensions for 4 side machiningmm140 x 140
Minimum panel dimensions for lengthwise machining only (LxW)mm240 x 60
Panel roller support openingmm500
Work table heightmm900
R0.07.15olimpic 500 – composition “HP T-ER2” (40)
 Electronic top presser positioning
62.10.74Panel spacer on infeed fence
62.15.03“Nesting” copying device kit
62.12.03“AAR” anti-adhesive unit
62.12.61Spray-mist device for edge finishing
62.12.96Spray-mist device for delicate edges
 “RT-V1” pre-milling unit
62.14.55Diamond tools for pre-milling unit H=64-no.2 knives
 “VC-VM” gluing unit
62.12.49Infrared ceramic lamp
62.15.08SGP-E additional glue pot  – manual glue supply (1,5 Kg)
 “K-2 Radius”  end cutting unit
 “R-HP Multiedge 2R” trimming-chamfering unit
 “Round 2-A Multiedge 1R” rounding unit
 “RAS-HP Multiedge 2R” edge scraping unit
62.15.04“RC-N” glue scraping unit
62.12.12“SP-V” brushing unit
 “eye-S” consolle (Control-Panel)
 “Maestro active edge” human-machine interface software (HMI)
 Qs Monitor software equipment for “eye-S”
 Maestro connect: basic set-up (cabling only, for later gateway installation)
10.09.98European safety regulations (CE norms)
93.07.31Volt 400 EU

 

Product video 1

PRODUCT VIDEO 2

PRODUCTS

Featured Products

How can I help you?